-
1 обычаи и практика
обычаи и практика
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
code of practice
A systematic collection of procedures outlining the established method of application of all relevant laws, rules or regulations to a specific endeavor. (Source: BLD)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > обычаи и практика
-
2 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
См. также в других словарях:
Code-switching — This article is about the use of more than one language in speech. For the use of multiple languages in writing, see Macaronic language. Sociolinguistics Areas of study … Wikipedia
code key — n. a key cut to a specific code rather than duplicated from a pattern key. it may or may not conform to the lock manufacturer s specifications … Locksmith dictionary
Code — redirects here. CODE may also refer to Cultural Olympiad Digital Edition. Decoded redirects here. For the television show, see Brad Meltzer s Decoded. For code (computer programming), see source code. For other uses, see Code (disambiguation).… … Wikipedia
Code page — is another term for character encoding. It consists of a table of values that describes the character set for a particular language. The term code page originated from IBM s EBCDIC based mainframe systems,[1] but many vendors use this term… … Wikipedia
Specific performance — is an order of a court which requires a party to perform a specific act, usually what is stated in a contract. It is an alternative to award/ for awarding damages, and is classed as an equitable remedy commonly used in the form of injunctive… … Wikipedia
Code folding — is a feature of some text editors, source code editors and IDEs that allows the user to selectively hide and display sections of a currently edited file as a part of routine edit operations. This allows the user to manage large amounts of text… … Wikipedia
code — n [Old French, from Medieval Latin codex, from Latin caudex codex tree trunk, set of wood writing tablets, book] 1: a systematic compilation or revision of law or legal principles that is arranged esp. by subject: as a: one that contains the law… … Law dictionary
Code page 437 — Code page 437, as rendered by the IBM PC using a VGA adapter. IBM PC or MS DOS code page 437, often abbreviated CP437 and also known as DOS US, OEM US or sometimes misleadingly referred to as the OEM font, High ASCII or Extended ASCII,[1][2] is… … Wikipedia
Specific Area Message Encoding — or SAME is the protocol used to encode the Emergency Alert System in the U.S. for broadcast stations. It was originally created for NOAA Weather Radio by the National Weather Service, and was later adopted by the FCC for regular broadcasters on… … Wikipedia
Code review — is systematic examination (often as peer review) of computer source code. It is intended to find and fix mistakes overlooked in the initial development phase, improving both the overall quality of software and the developers skills. Reviews are… … Wikipedia
Code Lyoko — Format Animated, Science fiction, Action, Comedy Created by Tania Palumbo Thomas Romain … Wikipedia
